www.zeroshell.org Forum Index www.zeroshell.org
Linux Distribution for server and embedded devices
 SearchSearch  RegisterRegister  UsergroupsUsergroups 
 ProfileProfile  Log inLog in  Log in to check your private messagesPrivate Message 

e1000e problem with 100mb line

Post new topic   Reply to topic    www.zeroshell.org Forum Index -> ZeroShell
View previous topic :: View next topic  
Author Message

Joined: 12 Aug 2013
Posts: 1

PostPosted: Mon Aug 12, 2013 5:24 pm    Post subject: e1000e problem with 100mb line Reply with quote


I've been using Zeroshell to net balance 4 regular ADSL lines for a while and having no problems. Recently added a new 100mb fiber line which I've tested with a laptop and get a solid 80+mbps through.

Am trying to hook it up to Zeroshell 2.0.RC3 using an Intel 82574L, e1000e module. I seem to get a maximum of around 5mbps if lucky (Upload seems to be closer to 60mb of a normal 80mb)

Ethtool reports:


Settings for ETH05:
        Supported ports: [ TP ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 100Mb/s
        Duplex: Half
        Port: Twisted Pair
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: pumbg
        Wake-on: g
        Current message level: 0x00000007 (7)
        Link detected: yes

Which is odd as the laptop would happily connect at 1000Mb/s Full duplex. If I force autoneg off, it will allow me to force full duplex on, but if I force 1000Mb/s it won't connect at all. It makes no difference between Full or Half duplex 100Mb/s, both are crippled speeds.

ifconfig reports:


ETH05     Link encap:Ethernet  HWaddr 68:05:CA:14:3D:29
          inet6 addr: fe80::6a05:caff:fe14:3d29/64 Scope:Link
          RX packets:69323 errors:0 dropped:0 overruns:0 frame:0
          TX packets:45055 errors:0 dropped:0 overruns:0 carrier:0
          collisions:2858 txqueuelen:1000
          RX bytes:94556904 (90.1 Mb)  TX bytes:4477788 (4.2 Mb)
          Interrupt:16 Memory:d83c0000-d83e0000

After an almost fresh reboot, and I'm guessing the collisions may be where the problem is, but I'm not sure where to start looking to fix it.



root@zeroshell root> modinfo e1000e
filename:       /lib/modules/3.4.56-ZS/kernel/drivers/net/ethernet/intel/e1000e/e1000e.ko
version:        1.9.5-k
license:        GPL
description:    Intel(R) PRO/1000 Network Driver
author:         Intel Corporation, <linux.nics@intel.com>
srcversion:     79D090433A2DEF6FB5FCD00
alias:          pci:v00008086d00001503sv*sd*bc*sc*i*
alias:          pci:v00008086d00001502sv*sd*bc*sc*i*
alias:          pci:v00008086d000010F0sv*sd*bc*sc*i*
alias:          pci:v00008086d000010EFsv*sd*bc*sc*i*
alias:          pci:v00008086d000010EBsv*sd*bc*sc*i*
alias:          pci:v00008086d000010EAsv*sd*bc*sc*i*
alias:          pci:v00008086d00001525sv*sd*bc*sc*i*
alias:          pci:v00008086d000010DFsv*sd*bc*sc*i*
alias:          pci:v00008086d000010DEsv*sd*bc*sc*i*
alias:          pci:v00008086d000010CEsv*sd*bc*sc*i*
alias:          pci:v00008086d000010CDsv*sd*bc*sc*i*
alias:          pci:v00008086d000010CCsv*sd*bc*sc*i*
alias:          pci:v00008086d000010CBsv*sd*bc*sc*i*
alias:          pci:v00008086d000010F5sv*sd*bc*sc*i*
alias:          pci:v00008086d000010BFsv*sd*bc*sc*i*
alias:          pci:v00008086d000010E5sv*sd*bc*sc*i*
alias:          pci:v00008086d0000294Csv*sd*bc*sc*i*
alias:          pci:v00008086d000010BDsv*sd*bc*sc*i*
alias:          pci:v00008086d000010C3sv*sd*bc*sc*i*
alias:          pci:v00008086d000010C2sv*sd*bc*sc*i*
alias:          pci:v00008086d000010C0sv*sd*bc*sc*i*
alias:          pci:v00008086d00001501sv*sd*bc*sc*i*
alias:          pci:v00008086d00001049sv*sd*bc*sc*i*
alias:          pci:v00008086d0000104Dsv*sd*bc*sc*i*
alias:          pci:v00008086d0000104Bsv*sd*bc*sc*i*
alias:          pci:v00008086d0000104Asv*sd*bc*sc*i*
alias:          pci:v00008086d000010C4sv*sd*bc*sc*i*
alias:          pci:v00008086d000010C5sv*sd*bc*sc*i*
alias:          pci:v00008086d0000104Csv*sd*bc*sc*i*
alias:          pci:v00008086d000010BBsv*sd*bc*sc*i*
alias:          pci:v00008086d00001098sv*sd*bc*sc*i*
alias:          pci:v00008086d000010BAsv*sd*bc*sc*i*
alias:          pci:v00008086d00001096sv*sd*bc*sc*i*
alias:          pci:v00008086d0000150Csv*sd*bc*sc*i*
alias:          pci:v00008086d000010F6sv*sd*bc*sc*i*
alias:          pci:v00008086d000010D3sv*sd*bc*sc*i*
alias:          pci:v00008086d0000109Asv*sd*bc*sc*i*
alias:          pci:v00008086d0000108Csv*sd*bc*sc*i*
alias:          pci:v00008086d0000108Bsv*sd*bc*sc*i*
alias:          pci:v00008086d0000107Fsv*sd*bc*sc*i*
alias:          pci:v00008086d0000107Esv*sd*bc*sc*i*
alias:          pci:v00008086d0000107Dsv*sd*bc*sc*i*
alias:          pci:v00008086d000010B9sv*sd*bc*sc*i*
alias:          pci:v00008086d000010D5sv*sd*bc*sc*i*
alias:          pci:v00008086d000010DAsv*sd*bc*sc*i*
alias:          pci:v00008086d000010D9sv*sd*bc*sc*i*
alias:          pci:v00008086d00001060sv*sd*bc*sc*i*
alias:          pci:v00008086d000010A5sv*sd*bc*sc*i*
alias:          pci:v00008086d000010BCsv*sd*bc*sc*i*
alias:          pci:v00008086d000010A4sv*sd*bc*sc*i*
alias:          pci:v00008086d0000105Fsv*sd*bc*sc*i*
alias:          pci:v00008086d0000105Esv*sd*bc*sc*i*
intree:         Y
vermagic:       3.4.56-ZS SMP mod_unload modversions PENTIUMII
parm:           debug:Debug level (0=none,...,16=all) (int)
parm:           copybreak:Maximum size of packet that is copied to a new buffer on receive (uint)
parm:           TxIntDelay:Transmit Interrupt Delay (array of int)
parm:           TxAbsIntDelay:Transmit Absolute Interrupt Delay (array of int)
parm:           RxIntDelay:Receive Interrupt Delay (array of int)
parm:           RxAbsIntDelay:Receive Absolute Interrupt Delay (array of int)
parm:           InterruptThrottleRate:Interrupt Throttling Rate (array of int)
parm:           IntMode:Interrupt Mode (array of int)
parm:           SmartPowerDownEnable:Enable PHY smart power down (array of int)
parm:           KumeranLockLoss:Enable Kumeran lock loss workaround (array of int)
parm:           WriteProtectNVM:Write-protect NVM [WARNING: disabling this can lead to corrupted NVM] (array of int)
parm:           CrcStripping:Enable CRC Stripping, disable if your BMC needs the CRC (array of int)

I believe there is a later e1000e module but I can't run make install.

Can anyone offer any information that may help??

Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    www.zeroshell.org Forum Index -> ZeroShell All times are GMT
Page 1 of 1

Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

Powered by phpBB © 2001, 2005 phpBB Group