www.zeroshell.org Forum Index www.zeroshell.org
Linux Distribution for server and embedded devices
 
 SearchSearch  RegisterRegister  UsergroupsUsergroups 
 ProfileProfile  Log inLog in  Log in to check your private messagesPrivate Message 

Lan intefaces not available on ibase FWA8206

 
Post new topic   Reply to topic    www.zeroshell.org Forum Index -> Networking
View previous topic :: View next topic  
Author Message
Sker



Joined: 19 Oct 2010
Posts: 8
PostPosted: Tue Oct 19, 2010 9:15 pm    Post subject: Lan intefaces not available on ibase FWA8206 Reply with quote
I am new to the zeroshell router firewall world . I have installed the 1.0.beta13 image on a 4Gb CF card on an ibase FWA8206 . and from the console the appliance seems to have booted successfully .

Unfortunately I can't get the web interface to work . When I checked console and check the network setup none of the Ethernet interfaces seem to be available. If I try to assign an I address to Eth00 I get an error saying the interface is invalid.

The FWA8206 comes with Six Intel 82547L PCI Express Gigabit LAN interfaces. Are the drivers for this interface included in the image ?

I am not a Linux expert so any advice on how / what to check or do next would be appreciated ?
Back to top
View user's profile Send private message
ppalias



Joined: 17 Dec 2008
Posts: 1151
Location: Athens, Greece
PostPosted: Wed Oct 20, 2010 11:02 am    Post subject: Reply with quote
On the console can you run these commands and paste the output here?
Code:
lspci
lsmod
ifconfig -a
Back to top
View user's profile Send private message Yahoo Messenger MSN Messenger
Sker



Joined: 19 Oct 2010
Posts: 8
PostPosted: Wed Oct 20, 2010 12:21 pm    Post subject: Reply with quote
Below is the o/p of the commands

Thanks
Sker

lspci
00:00.0 Host bridge: Intel Corporation 82Q35 Express DRAM Controller (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82Q35 Express Integrated Graphics Controller (rev 02)
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02)
00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02)
00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02)
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 02)
00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 02)
00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 02)
00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02)
00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92)
00:1f.0 ISA bridge: Intel Corporation 82801IB (ICH9) LPC Interface Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801IB (ICH9) 2 port SATA IDE Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02)
00:1f.5 IDE interface: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE Controller (rev 02)
01:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
02:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
03:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
04:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
05:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
06:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
07:01.0 Mass storage controller: Integrated Technology Express, Inc. ITE 8211F Single Channel UDMA 133 (rev 11)


root@zeroshell root> lsmod
Module Size Used by
dummy1 5376 0
xt_CONNMARK 5760 1
tun 13696 0
bridge 57752 0
llc 9228 1 bridge
iptable_nat 9224 1
xt_state 4352 4
xt_tcpudp 4992 11
iptable_mangle 5248 1
iptable_filter 5376 1
ip_tables 16144 3 iptable_nat,iptable_mangle,iptable_filter
x_tables 19076 5 xt_CONNMARK,iptable_nat,xt_state,xt_tcpudp,ip_tables
nf_nat_pptp 5632 0
nf_nat_proto_gre 4740 1 nf_nat_pptp
nf_nat_ftp 5248 0
nf_nat 21656 4 iptable_nat,nf_nat_pptp,nf_nat_proto_gre,nf_nat_ftp
nf_conntrack_ipv4 19720 8 iptable_nat,nf_nat
nf_conntrack_tftp 7060 0
nf_conntrack_pptp 8964 1 nf_nat_pptp
nf_conntrack_proto_gre 8064 1 nf_conntrack_pptp
nf_conntrack_irc 8604 0
nf_conntrack_sip 11156 0
nf_conntrack_ftp 11300 1 nf_nat_ftp
nf_conntrack_h323 51912 0
nf_conntrack 67668 14 xt_CONNMARK,iptable_nat,xt_state,nf_nat_pptp,nf_nat_ftp,nf_nat,nf_conntrack_ipv4,nf_conntrack_tftp,nf_conntrack_pptp,nf_conntrack_proto_gre,nf_conntrack_irc,nf_conntrack_sip,nf_conntrack_ftp,nf_conntrack_h323
dummy 5376 0
vfat 14976 0
fat 54432 1 vfat
uhci_hcd 26892 0
ehci_hcd 38540 0
iTCO_wdt 14116 0
iTCO_vendor_support 5764 1 iTCO_wdt
ata_generic 10244 0
ata_piix 24068 0
pata_it821x 13572 0
libata 165192 3 ata_generic,ata_piix,pata_it821x
dock 12304 1 libata
loop 20100 1



root@zeroshell root> ifconfig -a
DEFAULTBR Link encap:Ethernet HWaddr B6:CB:7A:7A:68:50
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

VPN99 Link encap:Ethernet HWaddr 00:FF:E9:77:5E:9E
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

VPN99:00 Link encap:Ethernet HWaddr 00:FF:E9:77:5E:9E
inet addr:192.168.250.254 Bcast:192.168.250.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

dummy0 Link encap:Ethernet HWaddr 7A:B3:8F:B8:D9:73
inet addr:192.168.141.142 Bcast:192.168.141.255 Mask:255.255.255.0
BROADCAST NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

dummy1 Link encap:Ethernet HWaddr 9E:EC:1A:91:7C:88
inet addr:192.168.142.142 Bcast:192.168.142.255 Mask:255.255.255.255
UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:149 errors:0 dropped:0 overruns:0 frame:0
TX packets:149 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:16059 (15.6 Kb) TX bytes:16059 (15.6 Kb)

root@zeroshell root>
Back to top
View user's profile Send private message
ppalias



Joined: 17 Dec 2008
Posts: 1151
Location: Athens, Greece
PostPosted: Thu Oct 21, 2010 7:27 am    Post subject: Reply with quote
There seems to be no module loaded to recognize the NICs. You either will have to compile the module by yourself or report it as a bug so that it will be included in the next version. Although I am sure it will be included in the next version that will have a newer kernel.
Back to top
View user's profile Send private message Yahoo Messenger MSN Messenger
Sker



Joined: 19 Oct 2010
Posts: 8
PostPosted: Mon Nov 08, 2010 11:51 am    Post subject: Reply with quote
I have got a copy of the drivers (e1000e-1.2.10.tar.gz) for the card but when I run the make install in the extracted src folder I get the following errors

Code:
root@zeroshell src> make install
Makefile:71: *** Kernel header files not in any of the expected locations.
Makefile:72: *** Install the appropriate kernel development package, e.g.
Makefile:73: *** kernel-devel, for building kernel modules and try again.  Stop.
root@zeroshell src>

Can you let me know how I should compile the module

Thanks
Back to top
View user's profile Send private message
ppalias



Joined: 17 Dec 2008
Posts: 1151
Location: Athens, Greece
PostPosted: Mon Nov 08, 2010 1:37 pm    Post subject: Reply with quote
Hope this post will help you. Smile
Back to top
View user's profile Send private message Yahoo Messenger MSN Messenger
Sker



Joined: 19 Oct 2010
Posts: 8
PostPosted: Mon Nov 08, 2010 3:33 pm    Post subject: Reply with quote
I was afraid you were going to point me to that . I tired this but am not a linux person so I was hoping there was a differnet option.

I'll try this again with hopefully some help from google on how to do the steps that are "not described here"Confused
Back to top
View user's profile Send private message
ppalias



Joined: 17 Dec 2008
Posts: 1151
Location: Athens, Greece
PostPosted: Tue Nov 09, 2010 7:46 am    Post subject: Reply with quote
You can always ask for some help if you get stuck.
Back to top
View user's profile Send private message Yahoo Messenger MSN Messenger
Sker



Joined: 19 Oct 2010
Posts: 8
PostPosted: Fri Nov 12, 2010 4:37 pm    Post subject: Reply with quote
Found an image that has the drivers and works fine on the hardware platform.


Code:
http://www.zeroshell.net/eng/forum/viewtopic.php?t=1787&highlight=e1000e


now my problem is that I need this on a CF card but don't know how to change this ISO to bootable IMG Question
Back to top
View user's profile Send private message
Sker



Joined: 19 Oct 2010
Posts: 8
PostPosted: Tue Nov 23, 2010 12:33 pm    Post subject: Reply with quote
Tried to make a bootable cf card from this but It fails to boot. Are there any good howto's on truning the iso into a bootable img

Thanks
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    www.zeroshell.org Forum Index -> Networking All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group