› Forums › Network Management › ZeroShell › Question about Zeroshell WDS Capabilities
- This topic is empty.
-
AuthorPosts
-
October 28, 2008 at 5:09 pm #41257
matthew.a.squires
MemberThere are two configuration types for WDS; Wireless Bridging (No Clients-STA) & Wireless Repeating (With Client-STA).
There are three authentication methods; WEP, WPA2-PSK & WPA2-TKIP.
These standards can change depending on Manufacture and Model.
These standards are not etched in stone, and there is currently no IEEE standard.My questions are:
Witch AP configuration does Zeroshell support?
Witch Authentication Method does Zeroshell Support?
Can I Authenticate the APs and or the Clients using RADIUS?October 29, 2008 at 9:35 pm #47061imported_fulvio
ParticipantIt should be supported any combination, but at the moment I cannot test them to be sure.
Let us know your tests.Regards
FulvioOctober 30, 2008 at 2:07 pm #47062matthew.a.squires
MemberI updated a Linksys router with DD-WRT (Linux OS) and tried to configure a WDS connection between the two and it did not work. The Linksys DD-WRT was to authenticating on Zeroshell.
The Zeroshell IP address for the WDS was set to 10.10.10.1
The Linksys DD-WRT IP Address was set to 10.10.10.2
I did not use any encryption and broadcasting its SIDD.
I tried the LAN and P2P option and DD-WRT but they will not connect.
I tired turning off the WAN and still not connection.
I even configured DHCP on Zeroshell and still no success on Linksys DD-WRT connecting.Using the Linksys DD-WRT as a client works fine, but that is not what I am trying to do.
Can you provide me with some directions on Zeroshell end? If you are knowledgeable on Linksys DD-WRT and is to provide direction, it would greatly be appreciated.
_________________
Thank You;
Matthew SquiresALSO
I am building a new Zeroshell router to configuring, test and push for deployment of a WDS Network.
***To Confirm My Understanding***
On Zeroshell #2, I set it up as in AP with WDS?
On Zeroshell #2 the SIDD and Security must be the same as on Zeroshell #1?
Zeroshell #1 & #2 WDS must be on the Subnet?With this, Zeroshell #2 will act as a Wireless Bridge and the IP Address assignments will still come from Zeroshell #1, is that correct?
November 2, 2008 at 2:55 pm #47063imported_fulvio
ParticipantOn Zeroshell #2, I set it up as in AP with WDS?
On Zeroshell #2 the SIDD and Security must be the same as on Zeroshell #1?
Zeroshell #1 & #2 WDS must be on the Subnet?With this, Zeroshell #2 will act as a Wireless Bridge and the IP Address assignments will still come from Zeroshell #1, is that correct?
Yes, it is correct.
Regards
FulvioJune 17, 2009 at 12:19 am #47064skumaran
MemberHello,
I have currently configured my Soekris board running Zeroshell in WDS mode and I feel it is working properly.
I have a question about using Zeroshell for configuring WDS.
Is it possible to use Zeroshell for configuring multihop WDS? For example I have one Root Access point(AP) and another in STA client mode. Both are connected through a WDS link. Is it possible for another motherboard running Zeroshell with WDS connect to the board with STA client mode and still talk to the root access point?
I am talking about something similar to the one below. All connected wirelessly
Root Access point —> STA client 1 –> STA client 2 –> Laptop
If some one has already done something similar to this please help me out
Thanks.
-
AuthorPosts
- You must be logged in to reply to this topic.