Xenek Stoehr

Forum Replies Created

Viewing 2 posts - 1 through 2 (of 2 total)
  • Author
    Posts
  • in reply to: Zeroshell for Raspberry Pi and Orange Pi #63843
    Xenek Stoehr
    Participant

    Hi, have more info on the ppp0 errors (PPPoE Dialler for VDSL2+ in Australia on IInet)

    Before connecting RTL USB LAN

    20:48:45
    pppd 2.4.7 started by root, uid 0
    20:48:45
    Using interface ppp0
    20:48:45
    Connect: ppp0 <–> /dev/pts/0
    20:49:16
    LCP: timeout sending Config-Requests
    20:49:16
    Connection terminated.
    20:49:16
    Modem hangup
    20:49:20
    Exit.

    After connecting LAN

    20:50:46
    pppd 2.4.7 started by root, uid 0
    20:50:46
    Using interface ppp0
    20:50:46
    Connect: ppp0 <–> /dev/pts/0

    Then same as usual

    20:51:17
    LCP: timeout sending Config-Requests
    20:51:17
    Connection terminated.
    20:51:17
    Modem hangup
    20:51:22
    Exit.

    PPPoE connection (xDSL and cable modem)
    Interface PPP0

    Modem connected to ETH01

    Checking ‘show info’ PPP0

    ppp0: <POINTOPOINT,MULTICAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 3
    link/ppp
    RX: bytes packets errors dropped overrun mcast
    0 0 0 0 0 0
    TX: bytes packets errors dropped carrier collsns
    0 0 0 0 0 0

    Checking ETH01

    ETH01: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
    link/ether 00:e0:4c:68:02:11 brd ff:ff:ff:ff:ff:ff
    RX: bytes packets errors dropped overrun mcast
    12296 114 0 0 0 0
    TX: bytes packets errors dropped carrier collsns
    3166 75 0 0 0 0

    same thing, over & over again.

    20:57:25
    pppd 2.4.7 started by root, uid 0
    20:57:25
    Using interface ppp0
    20:57:25
    Connect: ppp0 <–> /dev/pts/0
    20:57:56
    LCP: timeout sending Config-Requests
    20:57:56
    Connection terminated.
    20:57:56
    Modem hangup
    20:58:01
    Exit.

    -tried again a few days later to allow for temp blacklist (no change)

    -added static IP in new subnet to ETH01 (no change)
    192.168.1.5 255.255.255.0

    -reboot while everything attached. (no change)

    -changed MTU from shell (no change)

    Any tips on new things to try?
    Thanks x

    in reply to: Zeroshell for Raspberry Pi and Orange Pi #63830
    Xenek Stoehr
    Participant

    Hi, am excited to have an alternative to openwrt.

    In particular, while you don’t support Odroid, I have ARM qemu KVM running on my Odroid XU4, and I hope to run your RPi version on the odroid, mostly because it supports gigabit Ethernet & USB3, with more ram, EMMC, 8 CPUs and also – I can put a large SSD for long term persistent, reliable storage of the DB. EMMC is great for OS, but better is always SSD, and with USB3, SSD is a valid option on XU4.

    This is my wish, but first I need it 100% on the core hardware, a Raspberry Pi 3B. Only after it’s good on there for a month will I try move it across.

    I’ve some problems, mostly of the ‘information’ sort. I’m a tech so can give any detail you need, but not a Linux genius so cmds to extract data & rough paths help. Happy to break this out into multiple posts if needed.

    -PPPOE doesn’t work (pad errors? Maybe blacklisted by my ISP? Never connects.)
    -only one of 4 usb-ethernet adaptors work, no info (even rough) on how to install driver (if I can find Linux Arm one)
    -no procedure to permanently swap eth00 and eth01 so PPPOE can connect (assuming ISP MAC blacklist exists)
    -If I remove eg. eth01 (rtl usb-eth) then unplug, then replug, it doesn’t reappear, even after a reboot (and no procedure to redetect it exists, as far as I can tell)
    -No tips on how to change more advanced PPPOE details (eg path to config file, details on which module is used)

    Note I’m not overly concerned about having a user-space PPPOE module, but it’ll become an issue if it’s overloading the CPU. Given I want to run it in KVM, I might be able to get you good feedback on usage if you need a tester for beta releases.

    Best,
    xenek

Viewing 2 posts - 1 through 2 (of 2 total)